Other products by Zalman
Item #: ZMFM2
Reg. Price: $4.99
Our Price: $4.99
Quantity:
 

Description 

The FANMATE 2 product is included with the many of Zalman's CPU coolers and the feedback has been so good that we are now offering it separately for customers who wish to use it with other fans. The FANMATE 2 is connected in-line with an existing fan and allows infinite control over the speed at which the fan runs. Where a fan is making a lot of noise due to excessive airflow, this can be reduced in a controlled manner, until such point as the noise becomes minimal and the airflow still adequate. The silencing effect of reducing the speed of a fan even by a small amount can be very surprising!

The FANMATE 2 has a small rotary knob which can be turned in either direction, to raise or lower the fan speed. Once you are happy with the noise/airflow setting, just leave the knob set in its position and your installation is finished. The best approach is to start with the FANMATE 2 at its minimum speed setting ("silent mode") and then increase the speed if more airflow is required.

Rather than using a simple rheostat (variable resistor) arrangement, the FANMATE 2 uses a high quality variable voltage regulator circuit which will not wear out or run excessively hot. Full instructions are supplied, and installation is very easy as can be seen in the diagram below. The product is intended to be used primarily with case fans, and you may be surprised how reducing the speed of a case fan (even slightly) can have a very large effect on noise output, with only a minimal effect on airflow. Of course the best approach is to use fans which are quiet to begin with, but if this is not possible, the FANMATE 2 will provide a very satisfactory alternative in your quest to reduce noise.

Fan Mate 2 Diagram

Although using the FANMATE 2 in conjunction with the fan on a CPU cooler is certainly possible, you would need to be careful to ensure that the processor does not get too hot due to inadequate airflow. If you have a CPU heatsink which is thermally inefficient in its design, then its manufacturer may have compensated for this shortcoming by providing it with a high-flow high-noise fan, usually because fast fans are cheaper than good heatsink designs! Using the FANMATE 2 in this scenario is not a good idea, and if budget allows, we would always recommend replacing the whole CPU cooler with one of the coolers we sell. This will guarantee safe cooling with the minimum possible noise level.

Please note that you must not use the FANMATE 2 in conjunction with any 12 volt fan having a power consumption in excess of 6 watts, or 0.5 amps. Damage to the fan and/or Fan Mate and/or PC system could otherwise occur. Virtually all but the very fastest/most extreme airflow fans consume under 6 watts and are therefore fine, but please check your fan specification before using the Fan Mate if in any doubt.

Finally, when using the FANMATE 2 at its minimum speed setting, you must ensure that the fan has a minimum startup voltage specification of not more than 5 volts. Otherwise, the Fan Mate will not give a high enough voltage to get the fan started from rest. Before finalising your installation, please test that all FANMATE 2-connected fans successfully start when you first power on the system. If you are using the FANMATE 2 with any of our Ultra-Quiet fans, you do not need to worry about this point because all our Ultra-Quiet fans are guaranteed to start at 5 volts.

Specifications

FAN MATE 2
Specifications
Dimensions (mm)
70 X 26 X 26 mm
Weight (g)
20
Output Voltage
5 ~ 11 VDC +/-2%
Allowable Wattage
6W or lower

*Please check the allowed wattage of the CPU fan connector on the motherboard, as well as the rated wattage of the fan to be used.
*Quiet PC USA, Inc. is not responsible for any damage to systems or CPUs caused by using the product outside of its specifications.
* Do not use FAN MATE 2 with a fan having a start up voltage of more than 5V. Please check the start up voltage in the specifications of the fan.